Omc Control Box Manual

Posted on  by

Omc Control Box Manual I have searched this forum, the internet, and the evinrude site for OMC style concealable remote control installation instructions with no results. I found the pre-delivery guide, but unfortunately it doesn't include specific instruction on this style of remote. TYPICAL CONTROL SYSTEMS OUTBOARD INBOARD/OUTBOARD Figure 2 SECTION 2 ASSEMBLE CONTROL 2.1 CONfIGURATION Normally the MN control should be obtained in the properly assembled configuration. Check your control with the assembly figures shown. ASSEMBLY 'A' FOR: MARINER OUTB'DS MERCURY OUTB'DS ( Except 18 & 25 ).

  1. Omc Control Box Manual
  2. Omc Control Box Manual
  3. Omc Outboard Control Box Manual
  4. Omc Remote Control Box Manual

Sections:

PREFACE

This flush mount, alternator tachometer is designed for use on the following:

  • Johnson® and Evinrude® Outboards

  • OMC Sea Drive® Models

  • NON-BRP products with 20 pole alternators

Installation

Disconnect battery cables to help prevent arcing or damage to equipment.

Select a tachometer mounting location that is in full view of the operator.

Omc Control Box Manual

Drill a 3-3/8 in. (86mm) hole in the dashboard.

Mount the tachometer so water will not collect on the face, or drip on the case and wires. If the tachometer is covered by a transparent shield, the shield must be adequately ventilated to help prevent sunlight heat soak damage.

Set Pulse Selector Switch

[1]
Align the arrow on the PUL/REV (pulses-per-revolution) switch (A) with the appropriate number.

  • Engines with two yellow stator wires (yellow and yellow/gray) set switch to '6'

  • Engines with three yellow stator wires (yellow, yellow/gray and yellow/blue) set switch to '5'

  • NON-BRP engines with 20 pole charging system, set switch to '3'

1968 THRU 1972 Outboards

If you are replacing an older Battery CD Ignition tachometer, or if the engine has never had a tachometer, move the engine harness gray wire to the rectifier yellow/gray circuit on the terminal board.

1978 and Newer Outboard and OMC Sea Drive

Use a wiring kit to connect the tachometer to the plug-in connector on the remote control or accessory electrical cable.

  • Use Plug-In Connector Kit P/N 0174732 when installing tachometer only.

  • Use Plug-In/Fuse Block Kit P/N 0173611 when installing tachometer with other accessories.

All Models

Use No. 8 insulated ring terminals and No. 16 A.W.G. wire of the specified color.

[1]
HELPFUL HINT: install star washer, ring terminal, and nut - in that order. This will help prevent ring terminal from rotating and loosening the nut. Connect all wires before installing gauge in dashboard.

[1]
Connect the following:

(B) To dashboard light switch, DARK BLUE WIRE.

(C) To alternator, GRAY WIRE.

OutboardOmc

Omc Control Box Manual

(D) To ground connection, BLACK WIRE.

(E) To key switch accessory terminal, PURPLE WIRE.

Insert the gauge into dashboard. Install bracket, star washers, and mounting nuts.

Do not overtighten the mounting nuts as you could permanently damage the gauge.

Omc

Omc Outboard Control Box Manual

Connect battery cables. Test the tachometer operation by running the engine.

Important: Multiple battery installations require a common battery ground cable. Refer to Outboard Installation Guidelines P/N 0508167.

Omc Remote Control Box Manual

[1]
To replace the light bulb, pry out light socket cover (F). Turn bulb socket counter-clockwise and pull out. Replace with a No. 194 bulb, P/N 0125432.